토요타
쇼크업소버 교환미국 · Stack Exchange★ 신뢰도 4.1 (높음)

토요타 캠리 수리 사례

2007년식 · ACV40 (2006-2011) · 2.4 자동

총 비용

-

공임

-

부품비

-

소요 시간

-

2026. 7. 11. 작업

난이도 & 준비물

난이도 보통⏱ 예상 120~240🔧 리프트🔧 특수공구

증상

2007 Toyota 4Runner, 6기통, RWD 모델에서 스티어링 휠에 과도한 유격이 발생. 핸들을 돌렸을 때 앞바퀴가 움직이지 않는데도 핸들에 너무 많은 유격이 있음.

처리 내용

다음 중 하나 이상의 부품이 원인일 수 있음: 스티어링 칼럼의 유니버설 조인트 마모, 스티어링 랙 마모, 볼 조인트 마모, 스티어링 랙 마운팅 부실. 차량을 정지한 상태에서 누군가가 스티어링 휠을 최대한 앞뒤로 흔들되 앞바퀴가 움직이지 않게 하면서, 위의 부품들을 검사하여 어느 부품이 유격을 발생시키는지 파악. 예를 들어 UV 조인트가 불량이면 조인트의 한쪽 끝은 움직이고 다른 쪽은 움직이지 않는 것이 보임. 스티어링 랙이 불량이면 입력 샤프트는 앞뒤로 움직이지만 허브 캐리어로 가는 타이 로드는 움직이지 않음. 스티어링 랙이나 볼 조인트를 교체할 경우 휠 얼라인먼트 조정이 필수임.

출처

이 사례는 Stack Exchange (미국)에서 수집한 데이터입니다.

신뢰도 4.1점(높음) — 출처 소스의 전문성/검증구조를 기준으로 산정된 점수이며, 정확성을 보장하지 않습니다.

원문 보기 ↗

다른 차종의 쇼크업소버 교환 사례

포르쉐

포르쉐 카이엔

M138 said: Clad-Hach said: For me everything about Maserati screams run a mile, why would anyone buy a car from a brand with a reliability record arguably worse than a JLR product.Yes some of them look good but if you're stuck on the hard shoulder that would be the last thing on your mind.If you take a similar vintage Porsche 996 compared to a Maserati 4200, the Maserati engine is bulletproof compared to the Porsche engine. Where Maserati falls short is something like a suspension part on a Maserati 4200 that is nla.The availability or price of parts on a Maserati can quite rightly receive c

미니

미니 쿠퍼

하부 볼 조인트가 녹슬고 손상되어 있으며, 여러 부품들이 부식된 상태. 분해 및 해체 작업 진행 중.

토요타

토요타 코롤라

Ste372 said: pocketspring said: The Celica had it's own engine line up, the 4AGE wasn't used in them. It was used in the Corolla GTi though.Yes I know it wasn't used in the Celica what I'm getting at is it would of upset the applecart. If it had a 4age in it. It would of been as quick, if not quicker than the Celica so why would anyone have spent double on buying a Celica every car has its place in a manufacturers line up. This was placed in the budget friendly coupe. Do you think putting the 1.6L 112bhp 4AGE engine in the Paseo would have made it quicker than the 2.0L 173bhp 3SGE engine mk6

BMW

BMW 5시리즈

mwstewart said: I'm going to treat it to a set of Bilstein B8 dampers and new OEM springs.I'm a bit surprised that Mr "American-spec non-sport" is planning to buy some B8 dampers:1. I can't recall whether you've fitted lowering springs to the Corsa (or if the ecoFLEX model is fitted with them as standard), but aren't B8s for cars with lowering springs, whereas B6s are for standard springs?2. When various BMW guys on here fit Eibach lowering springs to their cars, they tend to fit B4S dampers as they've found B8s to be too firm.