포드
쇼크업소버 교환미국 · Stack Exchange★ 신뢰도 4.1 (높음)

포드 레인저 수리 사례

1998년식 · 3세대 (1998-2011) · 2.5 기본형

총 비용

-

공임

-

부품비

-

소요 시간

-

2026. 8. 14. 작업

난이도 & 준비물

난이도 보통⏱ 예상 120~240🔧 리프트🔧 특수공구

증상

랜저의 뒷쪽 좌측 타이어에서 브레이크액이 심하게 누출됨. 휠을 제거한 후 휠 실린더가 심하게 부식되어 거의 떨어져 나간 상태를 발견. 슈와 스프링도 유사한 상태. 모든 부품(슈, 스프링 키트, 앞 디스크 패드, 캘리퍼 볼트와 핀, 브레이크 라인 볼트, 블리더)을 교체하고 에어 빼기를 시작했으나 미완료.

처리 내용

뒷 브레이크 슈를 조정했는지 확인하세요 (드럼 브레이크 가정). 조정하지 않았다면 슈와 드럼 사이에 큰 간격이 있어서 브레이크가 작동하지 않을 수 있습니다. 조정기(adjuster)가 올바르게 설치되었는지 확인하세요. 에어 빼기를 할 때 사람이 브레이크 페달을 밟았는지, 아니면 자동 공구를 사용했는지 확인하세요. 자동 공구를 사용했다면 수동으로 브레이크 페달을 펌프질 한 후 압력이 돌아오는지 확인하세요 (마스터 실린더에 액체가 충분히 채워져 있어서 공기가 흡입되지 않았다고 가정).

출처

이 사례는 Stack Exchange (미국)에서 수집한 데이터입니다.

신뢰도 4.1점(높음) — 출처 소스의 전문성/검증구조를 기준으로 산정된 점수이며, 정확성을 보장하지 않습니다.

원문 보기 ↗

다른 차종의 쇼크업소버 교환 사례

포르쉐

포르쉐 카이엔

M138 said: Clad-Hach said: For me everything about Maserati screams run a mile, why would anyone buy a car from a brand with a reliability record arguably worse than a JLR product.Yes some of them look good but if you're stuck on the hard shoulder that would be the last thing on your mind.If you take a similar vintage Porsche 996 compared to a Maserati 4200, the Maserati engine is bulletproof compared to the Porsche engine. Where Maserati falls short is something like a suspension part on a Maserati 4200 that is nla.The availability or price of parts on a Maserati can quite rightly receive c

미니

미니 쿠퍼

하부 볼 조인트가 녹슬고 손상되어 있으며, 여러 부품들이 부식된 상태. 분해 및 해체 작업 진행 중.

토요타

토요타 코롤라

Ste372 said: pocketspring said: The Celica had it's own engine line up, the 4AGE wasn't used in them. It was used in the Corolla GTi though.Yes I know it wasn't used in the Celica what I'm getting at is it would of upset the applecart. If it had a 4age in it. It would of been as quick, if not quicker than the Celica so why would anyone have spent double on buying a Celica every car has its place in a manufacturers line up. This was placed in the budget friendly coupe. Do you think putting the 1.6L 112bhp 4AGE engine in the Paseo would have made it quicker than the 2.0L 173bhp 3SGE engine mk6

BMW

BMW 5시리즈

mwstewart said: I'm going to treat it to a set of Bilstein B8 dampers and new OEM springs.I'm a bit surprised that Mr "American-spec non-sport" is planning to buy some B8 dampers:1. I can't recall whether you've fitted lowering springs to the Corsa (or if the ecoFLEX model is fitted with them as standard), but aren't B8s for cars with lowering springs, whereas B6s are for standard springs?2. When various BMW guys on here fit Eibach lowering springs to their cars, they tend to fit B4S dampers as they've found B8s to be too firm.