토요타 캠리 수리 사례
2014년식 · ACV50 (2011-2017) · 하이브리드 2.5
총 비용
-
공임
-
부품비
-
소요 시간
-
2026. 7. 1. 작업
난이도 & 준비물
증상
2014 지프 패트리엇의 트랜스미션 교체 후 가속할 때, 감속할 때, 트랜스미션이 시프트할 때 소음이 발생합니다. 트랜스미션을 다시 교체했지만 소음은 계속되고 있으며, CV샤프트도 교체했으나 문제가 해결되지 않았습니다.
처리 내용
비디오를 여기에 올려보세요. YouTube에 먼저 업로드해야 할 수도 있습니다.
출처
이 사례는 CarTalk (미국)에서 수집한 데이터입니다.
신뢰도 2.5점(참고용) — 출처 소스의 전문성/검증구조를 기준으로 산정된 점수이며, 정확성을 보장하지 않습니다.
원문 보기 ↗토요타 캠리 다른 정비 사례
Some great threads running at the moment.So, of the cars you have owned, which three were the most enjoyable to drive?Edited to add… runners up can be included Edited by baconsarney on Tuesday 1st September 10:46
Some great threads running at the moment.So, of the cars you have owned, which three were the most enjoyable to drive?Edited to add… runners up can be included Edited by baconsarney on Tuesday 1st September 10:46
Some great threads running at the moment.So, of the cars you have owned, which three were the most enjoyable to drive?Edited to add… runners up can be included Edited by baconsarney on Tuesday 1st September 10:46
Some great threads running at the moment.So, of the cars you have owned, which three were the most enjoyable to drive?Edited to add… runners up can be included Edited by baconsarney on Tuesday 1st September 10:46
다른 차종의 변속기 오일 교환 사례
포르쉐 카이엔
NGK210 said: Yes, Henry and Harry have pukka aotomotive journo chops and are good in front of the camera. But, both suddenly become timid when in the presence of big guns. For example, compare Henry s take on the Porsche- / Preuninger-hosted preview of the 991 (992?) GT3 with Harris s. Henry was starstruck and followed the PR script to the point of tedium. Whereas Harris went well off piste, and his GT3 preview was the more interesting TV moment . Similarly, Harris literally sits down and has a few bevvies and a laugh with Singer s Dickinson and Fawaz, whereas others simply fawn. Harry is di
차량 정보 없음
I need to make some gears/pinions myself. I have access to a high quality 4-axis CNC mill, but not to a lathe. I'd like to cut these gears out of flat stock (facing), rather than round (edgewise) using narrow end mills. Being able to prototype this in plastic sheets is important to me. I've found a bunch of sites that explain hobbing and that have formulas for pitch etc, but no sites that actually generate the splines for the gear teeth to turn into Gcode. Before I sit down with Mathematica and derive it from first principles, does anyone know of a good resource for this?
쉐보레 말리부
1997 Chevy Blazer 4WD 4.3L V6 - 트랜스미션 팬에 구멍이 있어서 누유 발생
차량 정보 없음
I don't have the capabilities to take a pic right now.