총 비용
-
공임
-
부품비
-
소요 시간
-
2026. 7. 19. 작업
1995 Acura Legend 뒷 상단 컨트롤 암(승객측) 교체 중 서브프레임의 너트를 고정하는 볼트를 제거하려다가 과도한 토크로 인해 볼트가 부러짐. 용접된 너트가 서브프레임 내부에서 파손되어 볼트가 자유회전하면서 고착됨. 볼트가 약간 빠져나왔지만 계속 걸려있음.
차량 부품 재활용 센터에서 상태 좋은 중고 서브프레임으로 교체하거나, 접근성이 있다면 서브프레임에 절단구를 만들어 용접된 너트에 펜치로 접근하거나 용접으로 너트를 고정시켜 고착된 볼트를 제거하는 방법도 있음. 너트 제거 후 원래 위치에 다시 용접하고 절단부를 용접으로 복원하면 됨.
출처
이 사례는 Stack Exchange (미국)에서 수집한 데이터입니다.
신뢰도 4.1점(높음) — 출처 소스의 전문성/검증구조를 기준으로 산정된 점수이며, 정확성을 보장하지 않습니다.
원문 보기 ↗포르쉐 카이엔
M138 said: Clad-Hach said: For me everything about Maserati screams run a mile, why would anyone buy a car from a brand with a reliability record arguably worse than a JLR product.Yes some of them look good but if you're stuck on the hard shoulder that would be the last thing on your mind.If you take a similar vintage Porsche 996 compared to a Maserati 4200, the Maserati engine is bulletproof compared to the Porsche engine. Where Maserati falls short is something like a suspension part on a Maserati 4200 that is nla.The availability or price of parts on a Maserati can quite rightly receive c
미니 쿠퍼
하부 볼 조인트가 녹슬고 손상되어 있으며, 여러 부품들이 부식된 상태. 분해 및 해체 작업 진행 중.
토요타 코롤라
Ste372 said: pocketspring said: The Celica had it's own engine line up, the 4AGE wasn't used in them. It was used in the Corolla GTi though.Yes I know it wasn't used in the Celica what I'm getting at is it would of upset the applecart. If it had a 4age in it. It would of been as quick, if not quicker than the Celica so why would anyone have spent double on buying a Celica every car has its place in a manufacturers line up. This was placed in the budget friendly coupe. Do you think putting the 1.6L 112bhp 4AGE engine in the Paseo would have made it quicker than the 2.0L 173bhp 3SGE engine mk6
BMW 5시리즈
mwstewart said: I'm going to treat it to a set of Bilstein B8 dampers and new OEM springs.I'm a bit surprised that Mr "American-spec non-sport" is planning to buy some B8 dampers:1. I can't recall whether you've fitted lowering springs to the Corsa (or if the ecoFLEX model is fitted with them as standard), but aren't B8s for cars with lowering springs, whereas B6s are for standard springs?2. When various BMW guys on here fit Eibach lowering springs to their cars, they tend to fit B4S dampers as they've found B8s to be too firm.